Farm Gate Installation in Central Kansas
Heavy-duty tube and wire-filled farm gate installation for Reno County operations near Haven, Hutchinson, and Wichita — sized for equipment and hung to swing true for years. Free on-site estimates and a 5-year workmanship warranty.
Gates That Earn Their Keep on a Working Place
A farm gate gets used hard and used daily. You're swinging it open with a feed bucket in one hand, backing a loaded trailer through it in the dark, and trusting it to hold a pen of cattle that lean on anything that'll move. River Creek Fence installs heavy-duty tube and wire-filled farm gates for working operations all over Reno County — from cattle outfits south of Hutchinson to crop ground and small acreages around Haven — and we build them to take the daily beating without sagging or popping a latch.
Owner Cody Yoder grew up around livestock and farm ground, so he knows the difference a gate makes when you're moving stock or running equipment. We size openings to your widest implement, not just your pickup — a gate that fits the truck but not the grain cart or the swather is a gate you'll fight every season. Standard tube gates run 4 to 16 feet, and for equipment lanes we'll set wider double-hung openings so a combine header or a wide drill clears without you folding mirrors or scraping paint.
Every gate is only as good as the post it hangs on, and that's where most farm gates fail. We set hinge posts deep in concrete below the Kansas frost line and brace them properly so the weight of a 16-foot gate doesn't lean the post over the first wet spring. Tight, square hanging plus the right hinge and latch hardware means your gate swings free on a still morning and still latches clean after a season of use.
Is a Tube Farm Gate the Right Call for Your Place?
Great for
- Galvanized tube and wire-filled gates shrug off rust, rot, and Kansas weather
- Sized to your widest implement so the grain cart and swather clear with room to spare
- Wire-filled panels hold calves and small stock that slip through open tube gates
- Hung on braced, concrete-set posts so heavy gates swing true for decades
- Heavy-duty hinges and latches you can work one-handed with stock pushing the gate
Things to know
- Wide equipment gates cost more — the bigger the opening, the heavier the gate and the hardware
- A long gate needs a properly braced hinge post or it'll lean and start to drag
- Tube-only gates let calves and small stock slip through unless you spec wire fill
- Drive-through gaps in low spots can hold water, so we plan the swing and drainage with you
Built to Hang Square Through Kansas Wind and Frost
The weak point on almost every farm gate is the hinge post. A long tube gate is a lot of leverage on that post, and in Central Kansas soil that swells when it's wet and bakes hard when it's dry, a shallow post leans within a year and the gate starts dragging the ground. We set hinge posts deep in concrete below the frost line and tie them into a braced corner assembly so the gate's weight is carried, not fought. The result is a gate that still latches clean after years of daily swinging.
Hardware does the rest. We hang gates on heavy bull-pin hinges so you can lift one off when you need to, and we fit chain or lever latches you can run one-handed while a cow's nosing the gate. For equipment lanes we'll hang a matched pair as a double gate with a drop rod in the center, so you get the full width when the combine's coming through and a snug close when it's not. Before we ever dig, we call in the Kansas 811 utility locate to keep your buried lines clear.
What Farmers and Ranchers Use Farm Gates For
From the equipment lane to the working pens, here's where a well-hung farm gate pays for itself across Central Kansas.
Equipment & Field Access
Wide double-hung openings sized for the combine, grain cart, and drill so nothing scrapes coming through.
Livestock Pens & Lots
Wire-filled tube gates that hold cattle and calves in working pens, alleys, and corral systems.
Ranch Entry & Driveways
A finished entry gate at the road that sets off the place and controls who comes and goes.
Walk & Drive Gates
From a handy walk-through to a full drive gate, we hang the right size for how you actually use the opening.
Pipe Fence Tie-Ins
Matched tube gates hung into a continuous pipe fence for entries, pens, and high-traffic gaps.
Hinges, Latches & Hardware
Heavy-duty bull-pin hinges, chain and lever latches, and drop rods picked to match the gate and the load.
Standard tube farm gates land at the lower end of this range, while wide equipment openings, double-hung pairs, and heavy hardware push toward the high end. Pricing is per gate, not per foot.
What Affects Your Farm Gate Installation Price
- Gate width — a 4 ft walk gate vs. a 16 ft equipment opening
- Tube-only vs. wire-filled panel for holding small stock
- Single gate vs. a matched double-hung pair with a drop rod
- Hinge-post and brace work, plus hinge and latch hardware
Ranges are general estimates for Central Kansas and are not a quote — your written on-site estimate is always free.
How We Install Your Farm Gate
On-Site Estimate & Sizing
We walk the opening with you, measure for your widest implement, settle on tube vs. wire fill, and call in the Kansas 811 locate before we dig.
Set & Brace the Hinge Post
We set the hinge and latch posts deep in concrete below the frost line and brace them so a heavy gate won't lean or drag down the road.
Hang the Gate & Fit Hardware
We hang the gate on heavy bull-pin hinges, level it square, and fit the latch — or a center drop rod on double openings — so it swings free and latches clean.
Test the Swing & Walk It With You
We work the gate through its full swing, check the latch one-handed, clean up the site, and back it with our 5-year workmanship warranty.
Farm Gate Installation FAQ
Size it to your widest implement with a little room to spare, not just your pickup. A lot of Reno County operations run 14- to 16-foot openings for the combine, grain cart, or wide drill, and we'll set a double-hung pair when you need even more clearance. Tell us what's coming through and we'll measure it out on site.
A plain tube gate is fine for equipment lanes and big stock, but calves and small animals will slip through the rails. If the gate closes off a pen or lot with smaller stock, we spec a wire-filled gate so nothing crawls under or between. We'll match it to what you're holding.
Almost always it's the hinge post. A long gate puts a lot of leverage on that post, and a shallow set leans over the first wet spring in Kansas soil. We set hinge posts deep in concrete below the frost line and tie them into a braced assembly so the gate's weight is carried and it keeps swinging square.
Sometimes — it depends on whether the existing post is set deep enough and braced to carry the gate weight. If it is, we'll hang to it; if it's a shallow T-post or a leaning corner, we'll set a proper hinge post so your new gate doesn't pull it over. Cody will tell you straight on the estimate.
Installed farm gates generally run about $200 to $2,500 or more per gate. A standard tube gate is at the lower end, while wide equipment openings, wire-filled panels, and double-hung pairs cost more because of the heavier gate and hardware. We price per gate, and a free on-site estimate gets you a written number.
Yes — that's most of what we do. Cody grew up around livestock and farm ground, so we set up working pens and alleys with wire-filled stock gates and run wider tube or double gates for equipment lanes. Often a place needs both, and we'll lay out each opening for how you actually use it.
Related services & resources
Need a Gate That Holds Up to Daily Use?
Get a free, on-site estimate on a heavy-duty farm gate sized and hung for your operation. Call Cody and we'll measure your openings.
Request Your Free Estimate
Fill out the form below and we'll get back to you within one business day.
Contact Details
Prefer to reach out directly? We're here to help.
Phone
(620) 899-5595
codeyoder@icloud.com
Address
Haven, KS 67543
Hours
Open Daily · 8 AM – 6 PM
Service Areas
Haven, Hutchinson, South Hutchinson, Buhler, Nickerson, Yoder, Pretty Prairie, Partridge, Arlington, Plevna, Mount Hope, Burrton, Halstead, Newton, Kingman, Sterling, Lyons, McPherson, Maize, Wichita, Pratt, Stafford